To get a clean machine, use these simple but effective tips on How To Clean Washing Machine Tub
Keeping the washing machine tub clean is vital for getting rid of mold and killing germs. It’s also important to keep it from developing rust which can be dangerous when mixed with water. What’s more, you should know that letting go on this task will only lead to a short lifespan of your machine.
Here are some steps you can take in order to have a clean machine:
Step 1: Remove any soil manually before putting the clothes in the machine . This way you’ll prevent a lot of dirt from going inside while you wash them. Sometimes stains won’t come out even if washed in hot water so make sure to remove them beforehand.
Step 2: Use vinegar for cleaning. Pour about 6 to 8 cups of it in the machine’s drum and leave it there for 15 minutes to act. After this time has passed, add some hot water and start the machine again. Throughout the whole process, you must open any door or lid so that both sides can get clean. Repeat if necessary.
Step 3: Clean the rubber seal with a toothbrush. This part is often neglected but contains germs that may spread through your clothing while washing them inside the machine. You can use dish soap in combination with hot water or any other cleaner designed specifically for rubber seals to do this task properly.
Step 4: Put baking soda between washer tub & agitator. This will eliminate any foul smell that may come out of the machine while washing.
Step 5: Bleach is often used to kill germs but you must keep in mind that bleach will damage your machine if left for too long. Spray it on, let act for a couple minutes and then wipe off with a damp cloth. Don’t rinse the tub afterwards because this can wash out the bleach right away. Instead, dry thoroughly before putting clothes inside again.
Step 6: Once finished with all these steps, leave the door or lid open so air can circulate properly within your washing machine. This way you’ll prevent mildew from forming on both sides of the drum.
Contents
How To Prevent Mold From Forming On Washing Machine Tub?
In order to have a mold-free machine, you should do the following:
Step 1: Clean the washing machine tub every two weeks. This way mildew won’t have time to form and grow.
Step 2: Make sure that both sides of the drum dry properly after each cycle. Don’t leave it for too long because mold will develop if left wet.
Step 3: Use baking soda in combination with warm water or vinegar when cleaning the rubber seal in order to remove stains and prevent foul smells from building up. Baking soda is great for absorbing odors while vinegar doesn’t contain chemicals which can damage your machine over time.
How To Deep Clean Your Front-Loading Washing Machine Tub?
If you have a front-loading washing machine, these steps on how to clean your washing machine will also help you get rid of germs and keep it looking new for years:
Step 1: Remove lint filter on the top part. This way you’ll allow water to flow freely during cleaning;
Step 2: Put baking soda on an old toothbrush and start scrubbing. There are specific cleaners out there which may be used instead but baking soda is great at removing stains without damaging your tub over time.
Step 3: Use dish soap with warm water in the same manner as when cleaning rubber seals . You can use vinegar or ammonia in place of dish soap for this step if desired.
Step 4: Leave all doors and lids open after cleaning. This way you’ll prevent mildew from forming inside the tub.
How To Clean A Washing Machine Or Washer Drum?
If you want a clean machine, it’s a good idea to clean both sides of the drum since that’s where most germs and dirt reside:
Step 1: Put baking soda between rubber seals . This will help lift away stains easily while absorbing any foul smell which may result from leaving dirty laundry inside for too long. Make sure to wear gloves whenever handling or applying bleach cleaners because they can irritate your hands badly.
Step 2: Use vinegar and hot water mixture instead of bleach in order to remove germs without damaging your washing machine over time. Baking soda and dish soap can be mixed with the same hot water in order to deep clean rubber seals and any stains that may be present.
Step 3: Always leave doors and lids open after cleaning. This way you’ll prevent mildew from forming and keep your machine looking new for years to come.
Here is a list of numbers of the washing machine which is reviewed by our experts.
- Washing Machine Under 8000
- IFB Washing Machine Front Load
- Best Water Filter For Washing Machine
- Best Washing Machines For Hard Water
How To Clean The Filter Of Your Front Load Washing Machine?
To make sure your front load washing machine stays clean, it’s important to do the following:
Step 1: Remove the lint filter. This way you’ll enable water to flow freely during cleaning.
Step 2: Use warm water and soap to clean the rubber seals . Add baking soda in order to remove stubborn stains.
Step 3: Leave doors open after cleaning. This will prevent mildew from forming inside the tub.
How To Clean Top Loading Washing Machine Tub?
Never assume that using vinegar or dish soap is enough when trying to deep clean your top-loading washing machine. These steps on how to keep a front load washing machine clean can also help you get rid of germs and keep it looking new for years:
Step 1: Remove the lint filter. This way water can flow easily during cleaning.
Step 2: Put baking soda on an old toothbrush and start scrubbing. There are specific cleaners out there that may be used instead but baking soda is great at removing stains without damaging your machine over time.
Step 3: Use dish soap with warm water in the same manner to clean rubber seals . You can use vinegar or ammonia in place of dish soap for this step if desired.
Step 4: Leave all doors and lids open after cleaning. This way you’ll prevent mildew from forming inside the tub. Keep it open until you have dry, mold free surfaces.
Recommended Post: How To Choose A Washing Machine Cabinet
How To Clean The Bottom Of A Washing Machine?
To make sure your top loading washing machine stays clean, it’s important to do the following:
Step 1: Remove the lint filter. This way you’ll enable water to flow freely during cleaning.
Step 2: Use warm water and soap to clean rubber seals. Baking soda can be added in order to remove tough stains.
Step 3: Leave all doors open after cleaning. This will prevent mildew from forming inside the tub.
How To Clean A Front-Loading Washing Machine With Stains?
If you want a clean machine, it’s a good idea to clean both sides of the drum since that’s where most germs and dirt reside:
Step 1: Put baking soda between rubber seals. This will help lift away stains easily while absorbing any foul smell which may result from leaving dirty laundry inside for too long. Make sure to wear gloves whenever this step is being performed because bleach cleaners can irritate your hands badly.
Step 2: Use vinegar and hot water mixture instead of bleach in order to remove germs without damaging your washing machine over time. Baking soda and dish soap can be mixed with the same hot water in order to deep clean rubber seals and any stains that may be present.
Step 3: Always leave doors open after cleaning. This way you’ll prevent mildew from forming inside the tub.
Conclusion
To clean the tub of your washing machine, mix a solution of 1/2 cup white vinegar and 2 cups water in a large bowl. Fill the bottom half with this mixture. Add two tablespoons of dish soap to the top part so it runs down into the other area while you turn on the wash cycle. Let it run through one complete cycle before turning off or unplugging from the power source.
When finished, wipe away any remaining residue with paper towels and dispose of them outside in order not to contribute to landfill waste (or reuse). Then simply rinse out your washing machine tub. This is an easy way to keep things fresh and sanitary for future loads of laundry.